I don't know why you would do this as they are pretty reasonable to buy online. Making steroids at home can be done, but it can be risky. To make your steroids, you first need to buy the powered products and steroid-making kits that you can convert into steroids. Making steroids from powder at home does have some benefits. However, you must not always expect a lot because you must do it properly to realize all these benefits.
But if you need to be on the safe side, you have to use the right ingredients. Some of these compounds people use to make steroids at home could harm their bodies. Steroid products not approved by the relevant regulatory bodies could land you in trouble big time. If possible, consult with an expert before engaging in any production that could potentially land you in trouble.
You really can't make a steroid at home. What you can do is isolate it from another compound. After separating it, you can put it into oil and inject yourself with the new substance. But remember taking and making steroids is not entirely legal. Only those steroids the FDA allows could be made without taking a risk; the rest are substances the authority and others around the world do not allow. Notably, the usefulness and safety of the steroid to your body matters. Otherwise, you will not only be going against the law but also putting yourself at risk by producing and consuming unsafe steroids.
Take 10 grams hormone (testosterone cypionate)
0.08ml Benzyl Alcohol = 2% BA
8ml Benzyl Benzoate = 20% BB
23.2ml oil, grape seed or sesame seed
Syringes 3cc & 5/10cc
18 or 20 gauge needles
Glass Beaker
Sterile filter
Put the powder in the beaker and add the Benzyl alcohol and benzyl benzoate. Heat over low heat until you dissolve the powder, draw out the solution with a syringe and pass it through a sterile filter.
Must Read: Top 10 China Powder Steroid Suppliers
When you talk about making steroids at home, you take a powdered form of the steroid and put it into an injectable medium. Experts have found the powder form of any steroid to be safer if you compare it with other states. Also, the injectable medium must not have any contaminants that could jeopardize the safety and overall integrity of the steroid.
Equipment:
To make the correct quantities of injectable substance from the powder, you must follow the instructions to convert grams of powder to milliliters of injectable substance. You should know that such weighing equipment is essential and purchase them in advance. Alternatively, you can borrow from a friend if you cannot meet the cost.
Read Our Article: Suicides As A Result Of Steroids Use
How to make Testosterone Enanthate at home? First, you will need to sterilize the oil by heating the oil to 212° F or 100°C.
Put 20ml of water in your vial with a syringe and mark the level. Remove 0.6 ml and draw again. You have two levels observed now at 19.4 ml and 20ml. Tip out the water and let it dry while allowing the oil to cool.
Put 5gm of powder in a vial, add oil to the 19.4ml mark, and top up to 20ml with benzyl alcohol. Seal and shake well, and your substance is ready for use. The concentration is now 250mg per ml. Inject 2ml weekly for ten weeks.
Sterilize the oil as per the above method. Into your vial, put 25ml water and mark the level and then take out 0.8ml and mark again. There are now two marks at 25ml and 24.2ml. Tip water out and let the vial dry while the oil cools.
Put 5gm Boldenone oil in the vial, add oil to the 24.2ml mark, and top up with benzyl alcohol. Shake well. The solution is at 200mg per ml and ready for injection. Inject 2ml a week for 12 weeks.
One makes these with purified water and not oil. You will need a vial or beaker that will hold 40ml of water for every gram of powder you are using. Fill the container with enough water to make the quantity of powder you are working with, so for 2 grams of powder, you need 80ml of water, mark the container.
For each gram, remove 0.1ml of water, i.e., 0.2 MLS. Now you have two marks, one for 80ml and one for 79.8ml. Remove water from a vial and let dry completely. Add 2 grams of powder and add water to the lower mark and top up with benzyl alcohol.
Seal and shake well. The powder will sink to the bottom, so you must shake it well before use. Use 2ml injections daily. Forget for a second that using anabolic steroids is against the law. Not remember that steroids bring a host of side effects that should make any sane person think twice.
It would help to consider the moral and ethical implications of making steroids at home before beginning the brewing process. There is one cause, the average skinny guy shouldn't supplement with steroids simply because you don't have to! Barring any genetic disorder, any healthy human being is capable of gaining lean muscle mass without pumping their body full of growth hormones and testosterone.
The making of steroids is not very difficult at the household level. It would be best if you were very careful with the sterilization. However, it is good to avoid using these steroids to be safe in the long run.
Winter workouts can be challenging, but with the right clothing, you can stay warm, comfortable,…
Natural bodybuilding competitions are designed to promote and celebrate athletes who build their physiques without…
Primal movements are fundamental, natural movements that our bodies are designed to perform. Incorporating these…
Nootropics in bodybuilding refer to supplements or substances that enhance cognitive functions such as focus,…
Bone broth has gained popularity in the fitness community, including among bodybuilders, due to its…
Sleeping positions can significantly impact muscle recovery for bodybuilders. Here's how: 1. Blood Flow and…
View Comments
You say"I don’t know why you would do to this as they are really quite reasonable to buy online"
but buying steroids online is illegal and has a greater chance of getting busted.
and this wasn't much help( no offense intended) because buying the powder from China is illegal as well